LogoLogo
Gen 2.1
Gen 3.0Gen 2.1Gen 3.1 & 3.2
Gen 2.1
Gen 3.0Gen 2.1Gen 3.1 & 3.2
  • Introduction
  • Kayak
    • Getting Started
      • Assemble your kayak power meter
      • Charge your kayak power meter
      • Configure your kayak power meter settings
        • Blade tip to hand distances
        • Blade tip to blade tip distance
        • Blade twist
        • Blade type attached to shaft
        • Blade tip to datum distances
    • Calibration
      • Zero Offset
        • Zero Offset calibration
      • Scale Factor
        • Blades-on Scale Factor Calibration
        • Scale Factor calibration
    • Advanced
      • Adjust your clamp
      • Remove and attach your sleeve
  • Dragon Boat
    • Assemble, Charge and Configure
      • Assemble
      • Charge
      • Configure
      • Sleep
  • High-Kneel Canoe
    • Getting Started
      • How to assemble a high-kneel canoe power meter
  • Outrigger Canoe
    • Getting Started
      • How to assemble an outrigger canoe power meter
      • How to set the outrigger canoe power meter settings
        • Blade tip to handle distance
        • Blade tip to bottom hand distance
        • Blade kickback angle
  • SUP
    • Getting Started
      • How to assemble a SUP power meter
      • How to set the SUP power meter settings
        • Blade tip to handle distance
        • Blade kickback angle
  • General
    • Web Bluetooth App
      • How to place the power meter in deep sleep
    • Updating Firmware
      • How to update the power meter firmware using the Web Browser
      • How to update the power meter firmware using nRF Connect
    • Real-time Data
      • How to pair a Garmin Forerunner 910XT with a power meter
      • How to pair a Garmin Edge 1030 with a power meter
    • High Speed Data
      • How to start/stop recording High Speed Data
      • How to download High Speed Data (ANT)
      • How to view High Speed Data
      • How to change the High Speed Data settings
    • Shaft Information
    • Model Descriptions
      • Power Meter
      • Power Meter w/ High Speed Data
    • Firmware Changelog
    • Manufacturer's Warranty
Powered by GitBook
On this page
  • Step 1. Attach the end of the measuring tape to the left blade tip
  • Step 2. Measure the distance from the left blade tip to the left hand
  • Step 3. Attach the end of the measuring tape to the right blade tip
  • Step 4. Measure the distance from the right blade tip to the right hand
  • Step 5. Enter the distances into the 'Blade tip to hand distances' setting
  1. Kayak
  2. Getting Started
  3. Configure your kayak power meter settings

Blade tip to hand distances

The distance from the left blade tip to the left hand and the distance from the right blade tip to the right hand.

PreviousConfigure your kayak power meter settingsNextBlade tip to blade tip distance

Last updated 5 years ago

Step 1. Attach the end of the measuring tape to the left blade tip

Step 2. Measure the distance from the left blade tip to the left hand

  • Measure from the left blade tip to the knuckle of the middle finger of the left hand (the hand closest to the left blade).

  • The left blade tip to left hand distance is 610mm in the example image below.

Step 3. Attach the end of the measuring tape to the right blade tip

Step 4. Measure the distance from the right blade tip to the right hand

  • Measure from the right blade tip to the knuckle of the middle finger of the right hand (the hand closest to the right blade).

  • The right blade tip to right hand distance is 610 mm in the example image below.

Step 5. Enter the distances into the 'Blade tip to hand distances' setting

the distance here is 610 mm