LogoLogo
Gen 3.0
Gen 3.0
  • Introduction
  • Kayak
    • Getting Started
      • Assemble your power meter
      • Charge your power meter
      • Configure your power meter settings
        • Blade tip to hand distances
        • Blade tip to blade tip distance
        • Blade twist
        • Blade type attached to shaft
        • Left blade tip to LED distance
    • Calibration
      • Zero Offset
        • Zero Offset calibration
      • Scale Factor
        • N channel Scale Factor calibration
        • O channel Scale Factor calibration
    • Advanced
      • Deep sleep
      • Adjust your clamp
      • Remove and attach your sleeve
  • Canoe/sup/dragon boat
    • Getting Started
      • Assemble
      • Charge
      • Configure
    • Calibration
      • Zero Offset
        • Perform a ZO calibration
      • Scale Factor
        • A channel Scale Factor calibration
    • Advanced
      • Deep sleep
      • Adjust your clamp
      • Remove and attach your sleeve
  • General
    • Web Bluetooth App
      • How to place the power meter in deep sleep
    • Updating Firmware
      • How to update the power meter firmware using the Web Browser
      • How to update the power meter firmware using nRF Connect
    • Real-time Data
      • How to pair a Garmin Forerunner 910XT with a power meter
      • How to pair a Garmin Edge 1030 with a power meter
    • High Speed Data
      • How to start/stop recording High Speed Data
      • How to download High Speed Data (ANT)
      • How to download High Speed Data (Automatic Script)
      • How to view High Speed Data
      • How to change the High Speed Data settings
    • Shaft Information
    • Model Descriptions
      • Power Meter
      • Power Meter w/ High Speed Data
    • Firmware Changelog
    • Manufacturer's Warranty
Powered by GitBook
On this page
  • Step 1. Remove the existing sleeve
  • Step 2. Apply masking tape to the shaft
  • Step 3. Apply tape to the end of the clamp sleeve
  • Step 4. Apply hot-melt glue to the spigot section of the shaft
  • Step 5. Heat up the glue on the shaft and pre-heat the sleeve
  • Step 6. Attach the clamp sleeve onto the shaft
  • Step 7. Allow the hot melt glue to cool and set and then remove the masking tape
  1. Canoe/sup/dragon boat
  2. Advanced

Remove and attach your sleeve

PreviousAdjust your clampNextWeb Bluetooth App

Last updated 3 years ago

The following instructions explain how to remove and install the sleeve section of your power meter shaft. The sleeve is a replaceable component of your power meter. A sleeve of a different length can be fitted to lengthen or shorten the shaft.

Step 1. Remove the existing sleeve

  • The sleeve is fitted to the shaft with hot-melt glue. Using a heat gun, heat up the glued end of the sleeve. The glued section is 75mm long. Take care not to overheat the shaft by heating gradually and frequently checking to see if the glue connection can be separated.

Step 2. Apply masking tape to the shaft

  • Allow a 35mm spacing between the end of the shaft and the edge of the tape.

Step 3. Apply tape to the end of the clamp sleeve

Step 4. Apply hot-melt glue to the spigot section of the shaft

  • Heat and spread evenly.

Step 5. Heat up the glue on the shaft and pre-heat the sleeve

Step 6. Attach the clamp sleeve onto the shaft

  • When the glue becomes melted and the clamp shaft warm, quickly assemble the sleeve onto the shaft. Slide the clamp sleeve down the shaft until the bottom edge meets the tape applied in Step 2. Align the “0 degree” marking on the clamp with the LED.

Step 7. Allow the hot melt glue to cool and set and then remove the masking tape

  • Applying the heat gun to any excess glue on top of the tape will allow the tape to be removed easily, removing the excess glue with it.

  • Any remaining excess hot melt glue can be rubbed away using Mineral Turpentine soaked rag.